How to Drill a Hole in a Glass Bottle for Lamps, Planters and Crafts
Share
Drilling a glass bottle is much easier than most people expect. With a diamond bit, the right setup and a little patience, you can turn a wine or liquor bottle into a lamp, a hanging planter or a candle holder. A diamond bit does not cut with teeth. It grinds, so the keys are keeping it wet, keeping it steady and letting it work without pushing.
The hardest part is the start. A bottle is curved and slippery, so the bit wants to skate across the surface before it bites. This guide shows how to stop that with a guide, and how to keep the glass cool and the dust down.
Safety first
- Wear safety glasses. Glass chips and fine glass dust can fly.
- Use a cordless drill. You are working with water, and a cordless drill keeps mains power away from it.
- Keep the glass wet while you drill. Water cools the bit and stops glass dust from going into the air.
- Wear gloves when you handle the bottle after drilling. The edge of a fresh hole is sharp.
- Do not drill a bottle that is cracked, chipped or very thin.
- Turn hammer mode off, if your drill has it.
What you need
- A diamond drill bit or hole saw in the size you need. The 10-piece diamond drill bit set (5/32 to 1 inch) with foam guide and case covers all the common bottle sizes in one set (see below).
- A cordless drill that runs at low speed
- A shallow tub of water, or a ring of clay or plumber's putty to hold a pool of water around the hole
- A guide: a foam insert guide, a moldable plastic guide, or masking tape (see below)
- A board, towel or non-slip mat to hold the bottle steady
- A pencil or marker, safety glasses and gloves
Choose the bit size
The right size depends on what the hole is for. Check your lamp kit, fitting or hanger before you drill, and measure it.
- The easy choice: a 10-piece set. The Drilax 10-piece diamond drill bit set includes ten small sizes: 5/32, 3/16, 1/4, 5/16, 3/8, 1/2, 5/8, 3/4, 7/8 and 1 inch. It is made for bottle lamps, planters and tile, and it comes with a foam positioning guide and a zippered case. You can try different sizes on your project without buying single bits.
- Cord holes for bottle lamps. Our 5/8 inch diamond hole saw is sized for bottle lamp cords. The 5-piece set (3/8 to 1 inch) includes that 5/8 inch size plus 3/8, 1/2, 3/4 and 1 inch. The 5-piece set (3/16 to 1/2 inch) covers smaller cord and fitting holes.
- Planters and hanging holders. Larger holes, such as the 3/4 or 1 inch size, suit drainage holes and hanging fittings. The 3-piece set (1/2, 3/4 and 1 inch) is a good fit. For a smaller starter set, the 3-piece set (1/4, 1/2 and 3/4 inch) covers the common smaller holes.

Choose a guide
A guide holds the bit where you want it, so it cannot slide around the curve of the bottle at the start. Pick one of these:
- Foam positioning guide. The 10-piece drill bit set comes with a foam guide that stops the bit from slipping and holds water to cool the cut. Our 3-, 5- and 10-piece hole saw sets in zipper cases also include a foam insert that centers the bit and holds cooling water.
- Moldable plastic guide. Press a small piece of moldable plastic over the spot you want to drill and let it harden. Drill through it with the same bit you plan to use on the glass. You now have a guide with a perfectly sized hole. You only need to make one per bit size, and you can also use it just to mark the spot, then drill without it.
- Masking tape. A couple of layers of tape over the mark gives the bit something to grip at the start.
Step by step
- Choose your bottle. Pick a bottle with no cracks or chips. Thicker glass, such as a wine or liquor bottle, is easier to drill than thin glass. Remove the label and clean the bottle.
- Decide where the hole goes. A hole near the base is common for lamp cords. A hole in the bottom works for hanging candle holders and planters. Mark the spot with a pencil or marker.
- Hold the bottle steady. The bottle must not roll or move. Lay it on a towel or a non-slip mat, or build a simple board with a hole to hold the bottle neck-down so you can drill from the bottom. Keep your hands clear of the area under the bit.
- Set up the water. Put the bottle in a shallow tub of water so the drilling spot stays wet. If the spot is flat, such as the base, you can instead build a ring of clay or plumber's putty around the mark and fill it with water. Never drill the glass dry.
- Position the guide. Put your guide over the mark so the bit sits where you want it. If you have no guide, hold the bit at a slight angle to cut a small groove on one edge, then straighten it slowly until the whole bit sits flat.
- Start slowly. Use low speed and very light pressure. Let the diamond bite in before you do anything else.
- Grind, don't push. The diamonds do the work. Pressing harder does not make it faster. It heats the bit and can crack the bottle.
- Keep it wet and steady. Lift the bit a little every few seconds so fresh water gets under it and the glass slurry clears out. Do not rock or twist the drill.
- Ease off at the end. As the bit breaks through, reduce pressure even more. The last thin layer of glass is where chipping happens.
- Check and clean. Rinse the bottle and look at the hole with a flashlight. Small chips on the edge are normal. A crack running out from the hole is not, so do not use that bottle. If the edge is rough, smooth it under water with a diamond burr.

Making a bottle lamp
For a lamp, drill the cord hole low on the bottle or in the base, so the cord leaves at the bottom. Use a proper lamp kit that is made for the purpose and follow its instructions for the electrical parts. A rubber grommet in the hole protects the cord from the glass edge. If you are not confident with the wiring, ask a qualified person to do it.

Ideas for other projects
- Hanging candle holders and planters, with a hole in the bottom
- Drainage holes in a bottle planter
- Wind chimes and garden art
- Bird feeders and craft projects
Tips for success
- Practice on a spare bottle. Your first hole is the hardest. Use a bottle you do not mind losing.
- Make a guide for each bit size. If you are making several lamps or planters, a guide gives you the same hole every time.
- Diamond bits wear. They are consumable tools. If a bit stops cutting well, replace it instead of pushing harder.
- Be patient. A steady drill and a wet bit beat speed. Rushing is the main reason bottles crack.
Frequently asked questions
Can you drill a hole in a glass bottle?
Yes. Use a diamond drill bit or hole saw, keep it wet, use a guide so it does not slip, and drill slowly with very light pressure.
What drill bit do you use for a glass bottle?
A diamond-coated drill bit or hole saw. A standard metal or masonry bit will not cut glass cleanly and can crack it. A 10-piece diamond set with sizes from 5/32 to 1 inch covers most bottle projects.
Do I need water to drill glass?
Yes. Water cools the diamond, carries the glass dust away and helps prevent chipping and cracking. Keep the bit and the glass wet the whole time.
Why does the bit keep slipping on the bottle?
Bottles are curved and smooth. Use a guide, such as a foam positioning guide, a hardened moldable plastic guide or tape, so the bit cannot skate before it bites.
What size hole do I need for a bottle lamp?
It depends on your lamp kit and cord. Our 5/8 inch bit is sized for bottle lamp cords, and the 10-piece set (5/32 to 1 inch) lets you try the sizes you need. Check your kit before you drill.
Why did my bottle crack when I drilled it?
The most common causes are too much pressure, drilling dry, a bottle that was already cracked or very thin, a bottle that was not held steady, and not easing off as the bit broke through.
Related guides
- How to drill a hole in a ceramic plate for tiered stands and holiday decor
- How to cut circles from a ceramic plate for mosaics and crafts
- How to choose diamond drill bits for glass, tile and stone
- How to drill a hole in a glass aquarium for a bulkhead
- How to drill sea glass without chipping or cracking
The golden rule
KEEP IT WET + USE A GUIDE + LIGHT PRESSURE + EASE OFF AT THE END
Diamond bits grind; they don't punch. Take your time, and you will get a clean hole in a glass bottle that is ready for your lamp, planter or craft project.