Drilling a hole in a glass aquarium with a diamond hole saw inside a plumber's putty water dam, next to a bulkhead fitting

How to Drill a Hole in a Glass Aquarium for a Bulkhead (Step by Step)

Drilling a glass aquarium is a skill that opens the door to sumps, overflows and clean plumbing, and it is much easier than most people expect. A diamond hole saw does not cut with teeth. It grinds, using thousands of tiny diamond particles, so the keys are the right size, a steady guide, plenty of water and no pressure. This guide walks through the whole job, from checking the glass to fitting the bulkhead.

Check for tempered glass first. Tempered glass cannot be drilled. It breaks into thousands of small pieces the moment the bit cuts into it. Some tanks use tempered panels, and different panels on the same tank can use different glass, so check the specific panel you plan to drill. Ask the manufacturer, look for a stamp or etched mark in a corner of the panel, or look at the glass through polarized sunglasses: tempered glass shows dark bands or a pattern. If you cannot be sure, do not drill it.

This guide is for glass tanks. Acrylic tanks need different bits and a different technique.

Safety first

  • Wear safety glasses and work gloves. Glass chips and dust can fly, and the edge of a freshly cut hole is sharp.
  • Drill the tank empty, clean and dry on the inside. Never drill a tank with water in it.
  • Inspect the panel first. Do not drill glass that already has cracks, deep scratches or large chips.
  • Keep power strips and plugs away from the water you are using on the bit.

What you need

  • A diamond hole saw matched to your bulkhead (see the size table below)
  • A guide: a suction guide, a hole saw kit with a water guide, a foam insert guide, or a wood template (see below)
  • A variable-speed drill with a clutch or torque setting
  • Masking or painter's tape, and old towels
  • Clean water, plumber's putty (optional), and a tub or tray to catch runoff
  • A tape measure, pencil or marker, safety glasses and gloves
  • Your bulkhead, in hand

Choose the hole saw size for your bulkhead

The hole you drill does not match the pipe size you plan to connect. It has to fit the bulkhead body. Here are typical hole sizes for the most common ABS bulkheads. Sizes vary a little by manufacturer, and Schedule 80 bulkheads usually need a slightly larger hole, so always check the spec sheet for the bulkhead you buy, and have it in your hand before you drill.

Bulkhead size Typical hole size Hole saw
1/2 inch 1-1/4 to 1-3/8 inch (about 32 to 35 mm) 1-1/4 inch kit with water delivery guide or 1-3/8 inch kit with water delivery guide
3/4 inch 1-1/2 inch (about 38 mm) 1-1/2 inch kit with water delivery guide
1 inch 1-3/4 inch (45 mm) 1-3/4 inch hole saw
1-1/4 inch 2 inch (about 50 mm) 2 inch hole saw
1-1/2 inch 2-1/2 inch (60 to 65 mm) 2-1/2 inch hole saw

Planning more than one size, for example a drain and a return? The 3-piece hole saw set (1-1/2, 1-3/4 and 2 inch) with guide and case covers three common sizes in one purchase.

Choose a guide

A guide holds the bit upright and in place, so it cannot skate across the glass when you start. Any of these will do the job:

  • Suction guide. The adjustable diamond drill guide with suction base locks onto smooth glass. Removable ball bearings hold the hole saw steady and square, and a coolant feed hole lets you run water onto the bit. Its two adjustable faces cover hole saws from 1/8 inch to 1-3/4 inch on one side and 7/8 inch to 3-1/4 inch on the other.
  • Water delivery guide kits. Our 1-1/4, 1-3/8 and 1-1/2 inch kits come with a guide that sticks to the surface with adhesive mounting gaskets, centers the bit and holds a pool of water around the cut.
  • Foam insert guides. Our hole saw sets that come in a PU zipper case (the 3-piece, 5-piece and 10-piece sets) include a foam insert that works as a guide. It centers the bit and holds cooling water, so you do not need to buy a separate guide.
  • A wood template. Cut a hole of the same size in a scrap board with a wood hole saw, and clamp or tape the board over your mark.

Step by step

  1. Confirm the glass is not tempered. Do this before anything else, and check the specific panel you plan to drill.
  2. Inspect the panel. Look for cracks, deep scratches and chips. Pick a different spot, or a different tank, if the glass is already damaged.
  3. Plan the position. Keep the edge of the hole at least 1 inch from every edge of the glass, since closer than that the glass can crack out to the edge. Allow for the tank trim and any nearby holes. Think about the whole bulkhead, not just the pipe: you need clearance on both sides of the glass for the flange, gasket, nut and the plumbing you will add later. Use the real bulkhead and fittings to check the layout, level and measure twice, and mark the center. Once you drill the hole, you are committed.
  4. Set up the tank. Lay the tank on a flat, level work surface with the panel you are drilling facing up, so you have more control and water stays around the cut. Support the tank evenly and make sure nothing underneath creates a pressure point against the glass. Place a folded towel under the hole to catch the glass disc.
  5. Position the guide. Put the guide over your mark. If it is a suction or clamped guide, secure it so it cannot move, and do not overtighten any clamps against the glass.
  6. Tape the inside. A few layers of tape over the hole on the inside face help hold the glass plug in place as it is cut out.
  7. Set up the water. Build a small dam around the hole with plumber's putty and fill it with clean water, use the guide's water pool, or feed a slow trickle through the guide's coolant hole. Keeping the bit wet cools it and carries glass slurry away from the cut. A dry diamond coating wears off fast.
    Diamond hole saw drilling glass inside a ring of plumber's putty filled with water to keep the bit cool
    Illustration: a plumber's putty dam holds a pool of water around the hole saw. Always drill the tank empty and dry inside.
  8. Set the drill. Turn hammer mode off, set the drill to low speed and use the lowest clutch setting. If the bit snags, the drill stops and clicks instead of twisting out of your hand and cracking the glass.
  9. Start slowly with very light pressure. Place the hole saw in the guide, hold the drill as straight as you can and let the bit grind. There are no teeth, so pushing does nothing helpful. It only adds stress. Let the diamonds do the work.
  10. Keep it wet and steady. Lift the bit slightly every so often so fresh water gets in and the glass slurry clears out. Avoid rocking, twisting or sideways pressure.
  11. Use zero pressure at the end. This is the most important moment. As the bit nears the back of the glass, it is thin and wants to chip. Ease off completely and let the last of the glass grind away gradually. Forcing it through can make the disc break free and chip the back.
  12. Remove the disc and inspect. Stop the drill, then lift out the glass disc and the tape. Rinse away the slurry and look at both sides of the hole, using a flashlight. Look for cracks running out from the hole. A few small chips on the cut edge can happen, but a crack means the panel should not be used, and the surface where the bulkhead gasket sits must stay flat and undamaged. Lightly smooth any sharp edges if needed.
  13. Test fit the bulkhead. Clean the hole and the bulkhead. Put the gasket against the flange and fit the flange on the inside of the tank, with the threaded part passing through to the outside. It should drop into the hole with no force. If it resists, the hole is too small for that bulkhead. Hand-tighten the nut and stop. Overtightening can damage the bulkhead or the glass.
  14. Clean up. Rinse all glass debris out of the tank, wipe the area with paper towels you can throw out, and then repeat for any other holes.

Tips for success

  • Practice on a spare tank. If you are nervous, find an old or free tank (larger tanks have thicker glass) and drill it first.
  • Use a guide every time. It also gives you identical, repeatable holes if you are drilling several tanks for a rack.
  • No guide? A guide or template is the safest way to start. Without one, some experienced drillers tilt the hole saw slightly to cut a shallow groove on one edge, then slowly straighten it so the whole saw sits flat. This is riskier. Starting at an angle can chip or crack the glass if one side breaks through before the other.
  • Diamond hole saws wear. They are consumable tools. If you are drilling several tanks, keep a spare bit, and replace a bit that has stopped cutting well instead of pushing harder.
  • Buy the bulkhead first. Measure the actual bulkhead before choosing the hole saw.

Frequently asked questions

Can you drill a hole in a fish tank?

Yes, if it is a regular (annealed) glass tank. You cannot drill tempered glass. Use a diamond hole saw, a guide, plenty of water and very light pressure.

What size hole saw do I need for a 1 inch bulkhead?

A 1-3/4 inch (45 mm) hole saw is the usual size for a 1 inch ABS bulkhead. Check your bulkhead's spec sheet, as some brands and Schedule 80 bulkheads need a different size.

Do I need a drill guide?

It is strongly recommended. A guide stops the bit from wandering at the start, keeps it square to the glass and holds water around the cut. A suction guide, a hole saw kit with a water delivery guide, the foam insert guide that comes with our zipper-case sets, or a wood template will all work.

How do I know if my aquarium glass is tempered?

Ask the manufacturer, look for a stamp or etched mark in a corner, or view the glass through polarized sunglasses and look for dark bands. Check the specific panel you plan to drill. If you are not sure, do not drill it.

Should I drill a fish tank wet or dry?

Wet. Water cools the diamond, flushes out the glass slurry and helps prevent chipping. Keep the bit wet the whole time.

Why did my aquarium crack when I drilled it?

The most common causes are too much pressure, starting at an angle without a guide, a hole too close to an edge, a drill torque that was too high and snagged the bit, uneven support under the tank, or tempered glass.

Can I drill a tank that has water in it?

No. Empty the tank and dry the inside first.

Related guides

The golden rule

CHECK THE GLASS + USE A GUIDE + KEEP IT WET + NO PRESSURE

Diamond bits grind; they don't punch. Take your time, especially in the last few seconds, and you will end up with a clean hole that is ready for your bulkhead.

Back to blog