Illustration of a person in safety glasses and work gloves using a cordless drill with a gold diamond hole saw to cut a round hole in a red brick wall, with a light mist of dust

How to Drill Through a Brick Wall for a Mini-Split Line Set

The hole for a mini-split line set is small, but it decides whether the install stays dry, drains properly and looks neat. You need a hole that fits the whole bundle (refrigerant lines, drain hose and cable), a slight downward tilt to the outside, a sleeve, and a seal that keeps air and water out. This guide covers cutting that opening through brick, block or concrete with a masonry hole saw. For general technique and dust control, see our guide to drilling through brick or concrete for AC lines, conduit and vents.

Check what is behind the wall before you drill. Look for wiring, pipes, gas lines and steel reinforcement, and keep clear of lintels over windows and doors. If the wall is reinforced concrete, load-bearing or historic, talk to a qualified contractor first.

This guide covers the wall opening only. Follow your unit's installation manual for connecting, evacuating and charging the refrigerant lines, and check what local rules require for refrigerant work.

What goes through the hole

A typical mini-split bundle has two insulated refrigerant lines, a condensate drain hose and a communication cable. One installer guide describes the drain hose as 5/8 inch inside diameter and running through the same sleeve of about 3 inches as the refrigerant lines and cable. Your unit's manual has the exact sizes, so check it before you buy a hole saw.

Choose the hole saw size

Typical guidance for a mini-split is a hole of 2-1/2 to 3 inches, and larger systems can need up to 3-1/2 inches. There is no universal size, because the hole has to fit your bundle plus any sleeve. Test-fit the sleeve against the hole saw before you start. If a sleeve is a snug fit in a 3 inch hole, step up to the next size.

Hole size Drilax hole saws
2-1/2 in Gold Series 2-1/2 in, Pro Series 2-1/2 in
2-3/4 in Gold Series 2-3/4 in
3 in Gold Series 3 in with drill guide, Pro Series 3 in
3-1/8 in Gold Series 3-1/8 in, or the 3-1/8 in carbide saw in the 9-piece SDS set
3-1/2 in (larger systems) Gold Series 3-1/2 in
Bigger sleeves or multiple lines Gold Series 4 in with drill guide, 4-1/2 in with drill guide

Which tool? The Gold Series bits run in a standard drill and run dry or with a little water. The Pro Series bits thread onto a 5/8-11 angle grinder, and the 2-1/2 inch and 3 inch sizes include a drill adapter. If you own a rotary hammer, the 9-piece carbide set and the 4-1/2 inch carbide saw have 12 inch rods for thicker walls. For diamond core bits, turn hammer mode off.

What you need

  • A masonry hole saw in the size above, and a drill with a side handle (or a rotary hammer or angle grinder, depending on the bit)
  • A small masonry bit for a test hole, a stud finder or scanner, a level, tape and a pencil
  • A wood hole saw if there is sheathing, framing and drywall behind the brick
  • A wall sleeve sized for your hole, expanding foam sealant, and exterior-rated sealant
  • A cold chisel to remove the core, dust sheets, a shop vacuum and a line set cover for outside
  • Safety glasses, hearing protection, gloves and a respirator rated for fine dust

Step by step

  1. Plan the route. Place the indoor unit and the outdoor unit following the manual, aiming for a short, straight line set. Check the manual for the allowed run length and height difference.
  2. Pick the exit point. Check inside for studs, wiring and pipes, and outside for lintels, weep holes, flashing and mortar joints. Choose a spot where the drain can slope downward all the way to the outside.
  3. Drill a small test hole. From the inside, drill a small pilot hole through the wall at a slight downward angle toward the outside. Check where it exits. Move your plan now if it lands on an obstruction.
  4. Cut the brick. Using the pilot hole as a reference, cut with the masonry hole saw from the outside, tilting the drill slightly down toward the exterior so the opening slopes out. Use light pressure, clear dust often and cut in stages, breaking out the core as you go. Stop before breaking through, then finish from the other side to avoid chipping the face of the wall.
  5. Open the rest of the wall. If there is sheathing, framing or drywall behind the brick, cut through them with a wood hole saw on the same center, after checking for wires and pipes in the cavity.
  6. Fit the sleeve. A sleeve lines the opening, keeps rough masonry edges off the lines and insulation, and gives you something rigid to seal against. Some sleeves telescope to fit different wall thicknesses, and others are plastic tubes you cut to length. Sleeves are usually described in the manual but not included with the unit, so buy one before you start.
  7. Feed the bundle through. Cover the open ends of the lines to keep dust out, bundle the refrigerant lines, drain hose and cable with the tape provided without squashing the drain hose, and feed them through gently so the insulation is not torn or the copper kinked.
  8. Seal the opening. In a solid masonry wall, a generous amount of expanding foam sealant inside the sleeve is usually enough to stop air getting through. In rodent-prone areas, one source suggests stuffing the sleeve with copper wool before foaming. Seal the outside edge with an exterior-rated sealant, and do not block the weep holes at the base of a brick veneer or seal off a drainage cavity.
  9. Check the drain. The drain needs a continuous downward slope from the indoor unit to the outside, and one installer guide recommends at least 1/4 inch of drop per foot of horizontal run. Follow your manual. If any section has to rise, you will need a condensate pump. Pour a cup of clean water into the drain pan and confirm it runs out.
  10. Finish outside. Fit a line set cover to protect the lines, and direct the drain discharge away from the foundation, walkways and plants.

Tips for success

  • Buy the sleeve first. Test-fit it against the hole saw so you pick the right size the first time.
  • Do not skip the slope. A drain that dips or runs flat can pool water and back up.
  • Protect the lines. Keep the ends covered while you drill and feed them through the sleeve, not past raw masonry.
  • Do not rely on the outside cover. A neat outside finish does not prove the wall is weatherproof, so check the seal from inside and out.
  • Keep a spare bit. Diamond bits are consumable and wear faster when they overheat or are pushed hard.

Frequently asked questions

What size hole do I need for a mini-split?

Typically 2-1/2 to 3 inches, with larger systems needing up to 3-1/2 inches. Check your unit's manual and test-fit your sleeve.

Can I use a 2 inch hole saw?

A 2 inch hole is usually too small for a full bundle with a drain hose and a sleeve. It suits smaller runs such as low-voltage cable.

Do I need a wall sleeve?

Manuals commonly describe one, and a sleeve makes it much easier to seal the opening and protect the lines. In poured concrete it protects the lines from rough edges, though it is not needed to air seal.

Why should the hole slope down toward the outside?

A slight downward slope helps condensate drain out and stops rain running back in. Follow the angle in your manual.

Can I drill through brick veneer and the wall behind it?

Yes. Use the masonry hole saw for the brick and a wood hole saw for the sheathing, framing and drywall. Check for wires and pipes first, and keep the weep holes clear.

Should I drill wet or dry?

Gold Series bits run dry on masonry, and a little water gives longer bit life and less dust. Control dust with a vacuum or shroud either way, and keep water away from electrical connections.

Related guides

The golden rule

RIGHT SIZE + SLOPE TO THE OUTSIDE + SLEEVE IT + SEAL IT, BUT NEVER BLOCK THE DRAINAGE

Plan the hole around the whole bundle, let the bit do the work and finish the opening so water goes out and stays out.

Back to blog